Report item
Item specifics
  • Model Number: FX2N
  • Brand Name: BETTERSHENGSUN
  • is_customized: Yes
  • Test1: 4
  • Test4: 4
Product Description
Model: XT2N-16MDR-A-V2 power supply: AC 220V baud rate: 9600/19200 communication port: serial port, RS485
Type: ladder direct writing (FX2N), relay points: 16 points completely run over GX8.5.
 
RS485 communication, RS instruction free communication protocol increased the CRC calibration, support for inverter and other communication.
A: This product currently supports the following resources:
Soft component:
X0-X31, Y0-Y31,
M0-M255, M512-M768 (blackout),
S0-S255,
T0-T87 (100mS, T200-T215 (timer timer), T250-T255 (10mS) 100mS integrated timer),
C0-C87, C112-C159 (16 power outage to maintain counter), C200-C203 (32 plus or minus power outage to maintain counter), C235 (32 bit high-speed addition and subtraction to maintain the counter),
D0-D115, D512-D559 (blackout)
Z0-Z7., N0~N7 P0~P8 V0-V7
Special soft element:
M8000 (running monitor contacts), M8001 (run monitoring anti contact).
M8002 (initial pulse contact), M8003 (initial impulse counter contact).
M8004 (error indicating contact).
M8011 (10 ms clock pulse), M8012 (100 ms clock pulse), M8013 (1 sec clock pulse), M8014 (1 clock pulse).
M8020 (zero mark), M8021, M8022 (carry flag) (carry).
M8029 (instruction execution end flag).
M8033 (memory hold contacts).
M8034 (no output contacts).
M8040 (transfer Forbidden) S0 the initial state of each operation
M8041 (transfer to revert to the initial state of S1 origin)
M8042 (initial pulse) S2 automatic operation of the initial state
M8050~M8053 were interrupted X0~X3
M8067 operation error flag
M8122 (RS)
M8123 (RS receiver)
M8147 (Y0 high speed output) M8148 (Y1 high speed output)
M8160 (high 8 and low 8 exchange with XCH instructions to use)
M8161 (ON) when the RS command is sent to the 8 bit, high cleared, OFF 16 bit sent
M8163 (CCD) ON when the verification instructions for the CRC, OFF for LRC verification
M8200-M8203 (C200-C203 count direction).
M8235 (C235 count direction).
D8000 (monitor timer setting value).
D8012 (maximum scan time).
D8120 (baud rate setting) default 9600
D8140 (Y0 pulse output counter register)
D8141 (Y1 pulse output counter register)
Support constant:
K range: -32768-32767 or 0-65535; H range: 0-FFFFH.
Currently does not support the 32 digit operation.
Maximum memory capacity: 8000 steps.
Two: This product currently supports the command set
This product currently supports the following commands for Fx2N:
Basic instruction:
LD, LDI, AND, ANI, OR, ORI, INV, OUT (T, C, S,),
SET (T, C, S), RST (T, C, S), ANB, ORB, LDP, LDF, ANDP, ANDF,,,,, and,
ORP, ORF, PLS, PLF, MPS, MRD, MPP, INV, MC, MCR, NOP,, END.,,, and
Contact comparison instruction:
LD>=, LD<=, LD>, LD<, LD<>, LD=, AND>=, AND<=, AND>, AND<, AND<>, AND=, OR>=, OR<=, OR>,, OR<, OR<>,, OR=.,,,,, and
Step instruction:
STL, RET.
Transfer and comparison instruction:
MOV, SMOV, CML, BMOV, FMOV, XCH, BCD, BIN, CMP, ZCP, FMOV., PRUN (with K bit transfer)
Four arithmetic instructions:
ADD, SUB, MUL, DIV, INC, DEC, WAND, WOR, WXOR, NEG.,
Cyclic shift instruction:
ROR, ROL, RCR, RCL, SFTR, SFTL, WSFR, WSFL,
FIFO instruction:
SFWR, SFRD
Cycle instruction:
FOR, NEXT.
Data processing instruction:
ZRST, DECO, ENCO, SUM, BON, MEAN, SQR, ASCI, HEX, SWAP, GRY,, GBIN,,, and
Analog quantity instruction:
RD3A, WR3A
Program flow instruction:
CJ (maximum 8 addresses), CALL (maximum 5 level nested, 8 subroutine), SRET, FEND, FOR (maximum 5 level nested), NEXT.
Interrupt instruction:
IRET, EI, DI increased along the I000~I300 down along the X0~X3 I001~I301
Convenient instruction:
ALT.IST
High speed processing instruction:
REF, REFF, MTR, PWM (support Y1, Y0 all the way, can be used at the same time), SPD (only support X0, X1 all the way), PLSY (only support Y0, Y1 all the way)
Peripheral I/O port:
MTR, TKY, DSW, HKY, SEGL, ARWS, ASC,, ASCI., SEGD.
Serial data transmission:
RS
Data check
CCD (LRC, CRC)
Analog read instruction
RD3A
Fully supports P instructions such as MOVP
This product currently does not support all 32 instructions in the Fx2N function instruction, that is, do not support functional instructions plus D, such as DMOV, does not support the ladder diagram reading function, no need to encrypt.
 
 
aeProduct.getSubject() aeProduct.getSubject() aeProduct.getSubject() aeProduct.getSubject() aeProduct.getSubject()

 

 

Packaging Details
  • Unit Type: piece
  • Package Weight: 0.5kg (1.10lb.)
  • Package Size: 10cm x 10cm x 10cm (3.94in x 3.94in x 3.94in)
Shipping
Calculate your shipping cost by country/region and quantity.
Quantity: Ship to:
Packaging Details
  • Unit Type: piece
  • Package Weight: 0.5kg (1.10lb.)
  • Package Size: 10cm x 10cm x 10cm (3.94in x 3.94in x 3.94in)
Payment
We support the following payment methods. All payments made on AliExpress are processed by Alipay.